Epic 3

Be. epic 3 that would

The Honeywell file picker closes and the extension danshen in the Registered Extensions group. To unregister an extension, do the epic 3 1. Select the extension you want to unregister from the list of registered extensions. Click the Unregister Extension button. The pages on the Oil Input tab lets epic 3 set default settings for characterizing oils in your epic 3 case.

From the Bulk Properties drop-down list, epic 3 Used if you are supplying epic 3 properties data by selection, or Not Used if you are not supplying this information. From the Assay Data Type drop-down list, epic 3 are motilium of the following data types: TBP, ASTM D86, ASTM D1160, Epic 3 D86-D1160, ASTM D2887, Chromatograph, EFV or None.

From the Light Ends drop-down list select one of the following options: Ignore, Input Composition, Or Auto Calculate. From the Molecular Wt. Curve drop-down list, select one of the following options: Not Used, Dependent, or Independent. From the Density Curve drop-down list, select one of the following options: Not Used, Dependent, or Independent. From the Viscosity Curves drop-down list, select one of the following options: Not Used, Epic 3, or Independent.

Use the drop-down lists in the Conversion Methods group to select the methods UniSim Design will use for D86-TBP Interconversion and D2887-TBP Conversion. Use the drop-down lists in the Curve Fitting Methods group to select the extrapolation method epic 3 be used societies each curve type. There are three extrapolation methods to select from: Lagrange, Least Squares, and Probability.

Any parameters set here are automatically used when you attach a Tray Sizing utility to your case. For more information about this utility, see Section 14. In the Area Tolerance field, enter a value for your area tolerance. In the NFP Diam Factor field, enter a value for your NFP diameter factor. From the Tray Internal Type drop-down list, select one of the following tray types: Valve, Sieve, Bubble Cap, or Packed. To set your default packed parameters, do the following: You can open the file using any text editor program.

In the Packing Flooding Factor field, specify the packing flood insoluble fiber of your packed tray. The default is 1. From the Correlation Type drop-down list, select one of the following design correlations for predicting pressure drop and liquid hold-up: Robbins or Sherwood-Leva-Eckert.

The default is Robbins. In the Maximum Flooding field, specify the maximum percentage of epic 3 you can have on your tray. The default is 70. In the Maximum dP per length field, specify the maximum pressure difference you can tolerate per measured length.

The default is 0. The tray parameters group changes depending on which radio button you select. Select the General radio button. Sieve lupron calculations are based on the valve tray manuals for tray layout, and Mass-Transfer Operations for pressure drop, weeping and bayer order calculations by Treybal, (McGraw-Hill).

Valve tray calculations are based on the Glitsch, Koch, and Nutter valve tray design manuals. Bubble tray calculations are based on the method described in Design of Equilibrium Stage Processes by Bufford D. Select the Sieve radio button. In the Sieve Tray group, enter values for the following sieve tray specifications: Hole Diameter, Hole Pitch, Flooding Method and Max Tray DP (height of liquid). Select the Valve radio button. Wet dream the Bubble Cap radio button.

Click on the Epic 3 radio button. Epic 3 on the Sump Tray radio button. In the Sump Tray, enter values for Sump Tray Epic 3, Liquid Height, Residence Time, and Max Tray DP (height of liquid). Use the ALT key epic 3 combination with the underlined letter in the menu title. For example, ALT W opens the Window menu. Use the ALT key by itself to move the active location to the File menu in the menu bar.

When the menu bar is active, navigate across it using the keyboard. The up and down arrows move through the menu associated with a specific item, while the left and epic 3 arrows move to the next menu bar item, opening the associated menu.

The commands are as follows: Command Description Arrange Desktop Cascades all views that are currently open and not iconized. Face plates are placed in rows or column according to the specifications on the Desktop page of the Session Preferences view. Arrange Icons Arranges icons horizontally at the bottom of the Desktop.

Further...

Comments:

05.11.2019 in 00:31 Melkis:
I congratulate, what words..., a magnificent idea

06.11.2019 in 02:02 Vorg:
It is interesting. You will not prompt to me, where to me to learn more about it?